쓰나미 신호 생성기
(Tsunami)
개요
- 본 쓰나미는 아두이노 플랫폼 기반의 강력하고 유연한 신호 생성기입니다.
- 아날로그 신호를 실험하기를 시작하는데 좋은 툴로 다양한 태스크를 수행할 수 있습니다.
- 아두이노 레오나르도와 Direct Digital Synthesis 칩을 결합하여 아날로그 신호를 믿을 수 없을 정도로 단순히 생성하여 냅니다.
- 거기에 유연한 입출력 회로를 추가하고, 사용하기 쉬운 소프트웨어 라이브러를 추가하여 아날로그 신호 작업을 LED 깜빡이는 작업처럼 쉽게 만들었습니다.
- 본 제품을 가지고 아래와 같은 작업을 할 수 있습니다.
- Use it as a building block for a synthesizer
- Measure unknown signals
- Measure the response curve of your audio amplifier
- Implement an APRS modem
- Generate precise clocks for other devices
- Make a digital theremin
- Read and write data tapes from classic computers (Commodore, Atari, etc)
- Test filters and reactive components (capacitors, inductors, and so forth)
- Encode and decode your own data for audio transmission
- Teach yourself about Direct Digital Synthesis
- Teach yourself about AC and complex impedance
- Make your own low frequency radio transmitter
- 아두이노 라이브러리는 쓰나미의 모든 기능을 커버하기 때문에 어떻게 하드웨어가 동작하는지 로우 레벨 디테일을 걱정할 필요가 없습니다.
- 쓰나미의 가장 기본적인 기능은 주파수 생성과 카운팅입니다. 2.5PPM의 크리스탈을 사용하여 높은 정교성을 가진 주파수를 만들어 낼 수 있을 뿐 아니라, 주파수 또한 그만큼 정교하게 측정이 가능합니다.
- 사인, 트라이앵글, 스퀘어 웨이브를 DC에서 2Mhz까지 생성할 수 있습니다.
- 진폭은 0에서 6V (Peak to Peak), DC offset은 양쪽 그라운드로 2V까지 조절이 가능합니다.
- 8Mhz까지 신호 측정이 가능하며, Phase delay를 검출 할 수 있으며, DDS(Direct Digital Synthesis)를 지원합니다.
특징
- Generate signals from DC to 2MHz.
- Supports sine, triangle, and square wave signals.
- Supports frequency, phase, and amplitude modulation.
- Adjustable signal amplitude up to 6 volts peak-peak (except square-wave).
- Can drive a 50 ohm load.
- Adjustable DC offset from -2V to +2V (except square-wave)
- Programmable over USB, and USB powered.
- Arduino Leonardo compatible ATMega32U4 microcontroller with 32KB flash and 2.5KB RAM.
- 2.5PPM Temperature Controlled Crystal Oscillator (TCXO).
- AD9838 Direct Digital Synthesis chip with 10 bit DAC.
- Expansion headers onboard for easy access to I2C and UART interfaces.
문서
연관제품
- 연관제품 1